A two component water-based epoxy resin floor coating for use on interior concrete and wood floors. It is an extremely tough, decorative glossy industrial epoxy floor coating.
If you know which product you need, please enter the product name and quantity. If you would like us to help you decide, please give a brief description of the space along with area size and whether internal or external.
Please enter the details of your quote request below, and we'll come back to you as soon as we can with your prices.
|Recommended Coats||two coats required|
Our water-based epoxy coating is an extremely tough, decorative industrial floor coating for use on interior concrete and wood floors. This floor finish is suitable for use in factories, warehouses, workshops, showrooms: anywhere durability and easy maintenance are important. This two-part epoxy resin is easily mixed and stays workable for two hours; giving you time to coat awkwardly sized areas or brush neat edges.
Features and Benefits of Water-based Epoxy Coat - Interior Floor Coating:
|Primer Required||Powerfloat Primer on power floated floors|
|Usage Interior / Exterior||interior|
|Properties||extremely tough, workable for two hours, easy to apply, hard-wearing and long lasting, can be used over existing coatings, virtually odorless|
|Coverage||approximately 250 sq. ft. per 1 gallon kit|
|Curing Time (hours)||12 hours at 60-70°F; full chemical resistance in 7 days|
|Pot Time (hours)||2 hours, less at higher ambient temperatures|
|Recommended Coats||two coats required|
Surface Preparation: The concrete surface must be clean, dry and free of loose material. New concrete should be allowed to cure for 28 days prior to coating. Remove oil, dirt, grease and other chemical contaminants by cleaning with detergent or other suitable cleaner. Rinse thoroughly. Use Cemtetch® to remove unsound laitance and create a proper surface profile to the concrete. Rinse thoroughly and allow to dry. Note: Concrete floors on grade must be free of moisture transmission from the ground. If there is any doubt about the dryness of the concrete, conduct a test by simply taping a piece of 4 mil plastic sheet 18" by 18" on the bare concrete for 24 hours. Be sure to tape all four sides. After 24 hours, check the concrete for signs of moisture. The concrete will be darker if damp. If moisture is found, allow additional drying time (10-14 days) and repeat test. Persistent moisture transmission will prevent proper performance of the coating. Please contact a Watco Industrial Flooring Expert at (855) 627-6350 for assistance. Also, check for curing compound or other types of sealers by pouring a small amount of water onto the concrete. If water soaks in, the surface is suitable for coating. If water beads up on the concrete, the surface is not porous and a test application is warranted to ensure proper adhesion will develop. Sanding or mechanical abrading may be required if proper adhesion does not develop. Previously coated floors need to be in good sound condition with proper adhesion to the concrete substrate. Check the adhesion of the previous coating by cutting a small X in the coating using a sharp razor knife, firmly apply a piece of 2" duct tape over the center of the X cut, then pull off with a fast snap. The coating is suitable to topcoat if no significant previous coating is removed beyond the X cut. If the coating fails this test, then additional surface preparation is required. It is recommended previously coated floors be sanded and vacuumed prior to application.
Mixing: Combine the base and activator components. Use a paint paddle or spatula to scrape out and transfer as much of the material as possible. Mix the components thoroughly until an even, uniform color is achieved. If using a power mixer use a paint paddle or spatula to blend in any unmixed material from the sides and bottom of the pail. Do not mix more than one unit at a time. Immediately pour the material into a roller pan and do not delay application. The pot life is 2 hours, less at higher ambient temperatures, and unused material will get hot and may pose a hazard.
Application: Apply in a well ventilated area when the air and surface temperatures are between 60-90°F (16-32°C). Use a good quality lint free 3/8" nap roller with a phenolic core. A brush may be used for cutting in along walls. Do not exceed the maximum published coverage rate per coat. Some colors may darken slightly as it cures and it should not be over rolled. Two coats on most surfaces will produce a tough, mid gloss finish. Surfaces of higher than normal porosity may require further coats.
Coverage: Coverage will vary with the porosity and the degree of surface profile of the concrete. For the purpose of estimating coverage, assume 250 sq. ft. per one gallon kit.